Roll Dryer Features: 1) Reforming for twisted veneers and drying of slicer are performed at one process. 2) Feeding speed and heat temperature are freely selected in accordance with the thickness of veneers and water content. 3) Double safety unit never causes an overheat. 4) Heat is generated through kerosene or steam. Upper-equipped roller and lower-equipped roller hold veneers at the same time,then the feeding is performed. The roller is plated to prevent from rust. And twisted veneers are corrected thanks to the effectiveness of the pressed iron.
VENEER DRYING SYSTEM

RD-6 RD-6J RD-8 RD-8J RD-8JW
Effective drying width(mm) 1,000mm -> -> -> 2000mm
Feed speed 2.2~9.2m/min(60Hz)

1.8~7.7m/min(50Hz)

-> -> -> 2.14~8.55m/min(50Hz)
Hot air circulating fan 3 fans with 3.7KW motor -> 4 fans with 3.7KW motor -> ->
Heat source
(automatic control) 		1 Kerosene burner(150W) 3 steam heaters(6kgf/cm2) 2 Kerosene burner(150W) 120治C MAX 4 steam heaters(10kgf/cm2)
Hot air temperature(automatic control) 150治C MAX 120治C MAX 150治C MAX 150治C MAX
Machine size(W*L*H) 2,325*6,297*2,493mm 2,345*6,377*2,545mm 2,325*8,245*2,485mm 2,345*7,727*2,595mm 2,900*8,300*2,800mm
Net weight 4,800kg 5,000kg 6,600kg 6,800kg 14,500kg

Wide space is not taken up due to the head running system. Easy to remove and install Knives with magnetic knife bed. Dangerous operation for sharpening knives can be done without any manual works with double stone head motors for rough and finish.Two-stage shift mode for feeding speed in rough and finish machining,and its maximum speed makes it possible to carry out the most precise and efficient grinding.
KNIFE GRINDER

GS-150 GS-200 GS-240 GS-300 GS-400
Work Capacity(Knife length) 1,500mm 2,000mm 2,400mm 3,000mm 4,000mm
Wheel size Grinding Ø150*100*Ø25.4mm -> Ø205*100*Ø38.1mm -> Ø205*100*Ø25.4mm
Lapping Ø100*50*Ø15.88mm -> -> -> ->
Power required Grinding 2.2KW 4P 3.7KW 4P -> -> ->
Lapping 0.4KW 4P -> -> -> ->
Pump 0.18KW 2P -> -> -> 0.25KW 4P
Feed 0.75KW 2/4P -> -> -> ->
Lapping head aut. indexing motor 0.4KW(option) -> 0.4KW -> ->
Feed speed 10.4/5.2m/min(60Hz)
8.7/4.3m/min(50Hz) 		-> -> -> ->
Machine size(W*L*H) 1,055*3,070*1,460mm 1,075*3,770*1,810mm 1,075*4,300*1,810mm 1,075*4,900*1,810mm 1,075*5,900*1,810mm
Net weight 1,900kg 2,100kg 2,200kg 2,400kg 3,500kg
Flitch conveyor system develops the ability of slicer dramatically. Materials,maximum 4 meter in length and 7 flitches, are carried on conveyor with merry-go-round system. Automatic follower conveyor to keep track of flitch thickness difference is available on order.



Flitch Conveyor System

SLC-25Y2 SLC-35Y2
Flitch size Length 2~4m 2~4m
Thickness 10~240 10~240
No.of flitch 1~4 1~4
Lengthways feed speed 60m/(min.) 60m/(min.)
Side feed speed 30m/(min.) 30m/(min.)
Table height 815 915